null
Skip to main content

Bob Smith Industries

  • BSI: Insta-cure (1/2oz)(101)

    Bob Smith Industries

    BSI: Insta-cure (1/2oz)(101)

    $4.99

    Insta-Cure™ has a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds. Surfaces to be bonded must be tight fitting and should be held...

  • BSI: Insta-cure (2oz)(103)

    Bob Smith Industries

    BSI: Insta-cure (2oz)(103)

    $11.99

    Insta-Cure™ has a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds. Surfaces to be bonded must be tight fitting and should be held...

  • BSI: Insta-cure+ (1/2oz)(106)

    Bob Smith Industries

    BSI: Insta-cure+ (1/2oz)(106)

    $4.99

    Insta-Cure+™ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps. Normally, the thicker CA is applied to one surface and then the parts are held tightly...

  • BSI: Insta-cure+ (2oz)(108)

    Bob Smith Industries

    BSI: Insta-cure+ (2oz)(108)

    $11.99

    Insta-Cure+™ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps. Normally, the thicker CA is applied to one surface and then the parts are held tightly...

  • BSI: Insta-Set pump (2oz)(151)

    Bob Smith Industries

    BSI: Insta-Set pump (2oz)(151)

    $6.99

    INSTA-SET™ is a catalyst which acts as an accelerator that allows CAs to quickly cure in thick layers by enhancing the alkaline conditions during polymerization. INSTA-SET™ in a spray...

  • BSI: Maxi-cure (1/2oz)(111)

    Bob Smith Industries

    BSI: Maxi-cure (1/2oz)(111)

    $4.99

    Maxi-Cure™ extra thick CA is the best CA for most plastics, including GE’s Lexan MAXI-CURE™ is the best choice for plastic model assembly. When used with INSTA-SET™, it works...

  • BSI: Maxi-cure (2oz)(113)

    Bob Smith Industries

    BSI: Maxi-cure (2oz)(113)

    $11.99

    Maxi-Cure™ extra thick CA is the best CA for most plastics, including GE’s Lexan MAXI-CURE™ is the best choice for plastic model assembly. When used with INSTA-SET™, it works...

  • BSI: Plastic-cure (1/2oz)(105)

    Bob Smith Industries

    BSI: Plastic-cure (1/2oz)(105)

    $8.99

    Plastic-Cure™ is a gap-filling formulation of CA that works best on plastics. It is packaged in a bottle with a brush built into its top, which in many cases is an easier way to apply the CA...

  • BSI: Super-Gold (1/2oz)(121)

    Bob Smith Industries

    BSI: Super-Gold (1/2oz)(121)

    $9.99

    SUPER-GOLD™ Thin and SUPER-GOLD+™ gap filling medium thickness are our odorless foam safe CAs. They are non-frosting and take only 2 or 3 seconds longer to bond compared to Insta-Cure and...

  • BSI: Uncure (1oz)(161)

    Bob Smith Industries

    BSI: Uncure (1oz)(161)

    $4.99

    UN-CURE™ debonder will soften cured CA. If parts are bonded incorrectly or your fingers are stuck together, a few drops of UN-CURE™ will dissolve the CA in about a minute. Apply on bonded...