Plastic-Cure™ is a gap-filling formulation of CA that works best on plastics. It is packaged in a bottle with a brush built into its top, which in many cases is an easier way to apply the CA. As long as brush is put back into the bottle after use, the bristles of the brush will not harden. Care must be taken, however, not to introduce foreign material into the bottle. The brush should not be used, for example, to apply CA to wood that has been freshly sanded. Plastic-Cure will also bond wood, but its brush applicator at times will not be the best way to apply it. Plastic-Cure is superior for the application of false nails and wraps on fingernails, where its brush is the preferred method of application.
Bob Smith Industries
BSI: Insta-cure (1/2oz)(101)
$4.79
Insta-Cure™ has a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds. Surfaces to be bonded must be tight fitting and should be held together...
Add to Cart
The item has been added
Add to Cart
The item has been added
Bob Smith Industries
BSI: Insta-cure+ (1/2oz)(106)
$4.79
Insta-Cure+™ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps. Normally, the thicker CA is applied to one surface and then the parts are held tightly together...
Add to Cart
The item has been added
Add to Cart
The item has been added
Bob Smith Industries
BSI: Maxi-cure (1/2oz)(111)
$4.79
Maxi-Cure™ extra thick CA is the best CA for most plastics, including GE’s Lexan MAXI-CURE™ is the best choice for plastic model assembly. When used with INSTA-SET™, it works better than any putty...
Add to Cart
The item has been added
Add to Cart
The item has been added
Bob Smith Industries
BSI: Insta-cure+ (2oz)(108)
$11.99
Insta-Cure+™ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps. Normally, the thicker CA is applied to one surface and then the parts are held tightly together...
Add to Cart
The item has been added
Add to Cart
The item has been added
Bob Smith Industries
BSI: Insta-cure (2oz)(103)
$11.99
Insta-Cure™ has a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds. Surfaces to be bonded must be tight fitting and should be held together...
Add to Cart
The item has been added
Add to Cart
The item has been added
Bob Smith Industries
BSI: Maxi-cure (2oz)(113)
$11.99
Maxi-Cure™ extra thick CA is the best CA for most plastics, including GE’s Lexan MAXI-CURE™ is the best choice for plastic model assembly. When used with INSTA-SET™, it works better than any putty...
Add to Cart
The item has been added
Add to Cart
The item has been added
Bob Smith Industries
BSI: Super-Gold (1/2oz)(121)
$9.99
SUPER-GOLD™ Thin and SUPER-GOLD+™ gap filling medium thickness are our odorless foam safe CAs. They are non-frosting and take only 2 or 3 seconds longer to bond compared to Insta-Cure and Insta-Cure+...
Add to Cart
The item has been added
Add to Cart
The item has been added
Bob Smith Industries
BSI: Insta-Set pump (2oz)(151)
$6.99
INSTA-SET™ is a catalyst which acts as an accelerator that allows CAs to quickly cure in thick layers by enhancing the alkaline conditions during polymerization. INSTA-SET™ in a spray bottle is...
Add to Cart
The item has been added
Add to Cart
The item has been added
Bob Smith Industries
BSI: Uncure (1oz)(161)
$4.99
UN-CURE™ debonder will soften cured CA. If parts are bonded incorrectly or your fingers are stuck together, a few drops of UN-CURE™ will dissolve the CA in about a minute. Apply on bonded skin and...
Add to Cart
The item has been added
Add to Cart
The item has been added